Tegniese ondersteuning

Tegniese ondersteuning

materiaal

Mill
Pre-Gegalvaniseerde
vlekvrye staal SS304
vlekvrye staal SS316
Aluminium
FRP / GRP


afwerking

G: Pre-Gegalvaniseerde / PG / GI - vir binnenshuise gebruik om AS1397
H: Hot Dip Gegalvaniseerde / HDG - vir buite gebruik om BS EN ISO 1461
S4: Stainless Steel SS304
S6: Stainless Steel SS316
P: laquà - vir binnenshuise gebruik om JG / T3045
A: Aluminium om AS / NZS1866
FRP / GRP: veselglas-versterkte plastiek
F: Vuur uit die bus na AS3013: 2005
Z: verzinkt - vir binnenshuise gebruik om BS EN 12329
E: Elektrolitiese Poleer - vir vlekvrye staal gebruik
M: Mill / ligte / Plain Steel ISO 4995

 

 

Minimum laag dikte en Mass op Monsters wat nie gecentrifugeerd (HDG)
Artikel en dis T hickness Plaaslike Coating Dikte (Mi nimum)

μm

Plaaslike Coating Mass (minimum)

g / m 2

Beteken Coating Dikte (minimum)

μm

Beteken Coating Mass (minimum)

g / m 2

staal> 6 mm 70 505 85 610
staal> 3 mm tot 6 mm 55 395 70 505
staal1,5 mm tot 3 mm 45 325 55 395
staal< 1,5 mm 35 250 45 325

 

 

inspeksie

Dimensie Inspection
Coating Dikte Inspection


Kabel Tray laai Inligting

Vrag toets volgens EN 61537: 2007
Q = verspreide belasting (eenvormig verspreide belasting)
Veiligheid Factor = 1.7
L = intermediêre span
F = defleksie = 1/100 van die intermediêre span (max.)
S = Splice plek
gestel beladings van toepassing op sagte staal produk net .
Besca se vrag toets is in ooreenstemming met NL 61537: 2001. In praktiese terme dek hierdie deurlopende / multi
span installasies, eweredig gelaai langs die lengte van, en oor die volle breedte van die skinkbord. Die einde strek in
these installations should be reduced to 0.75 of the intermediate spans.
DEFLECTION: Besca’s load and deflection figures are in accordance with EN 61537:2007, with the characteristic
deflection of Unistrut Cable Tray limited to span/100 and load figures inclusive of a safety factor of 1.7.
ACCESSORIES: To ensure adequate support, accessories should be supported locally.
COUPLERS: The loading and deflection tables for Unistrut Cable Tray assume that the couplers are located at the
most onerous position within the span (i.e. mid span). To maintain the load/deflection figures stated in the tables,
the couplers should not be located in end spans or over support locations. Straight couplers were utilized for the
testing of the medium and heavy duty cable trays. Only one pair of couplers should be used per span.

Breedte (mm) Nuttige Cross Afdeling (cm 2)
lig Duty medium Duty Swaardiens
50 5.4 11.4 -
75 8.1 17.4 35.8
100 10.9 23.5 48.1
150 16.6 35.6 72,7
225 24.9 53.7 108,2
300 49.9 70.4 144,8
450 75.1 106,1 213,6
600 95,3 141,8 285,6
750 119,3 171,1 357,6
900 143,3 205,6 429,6